Overview Specifications Diagram Support Downloads Get A Quote  
Sorensen ASD Series Specifications
Voltage Ranges 342VAC to 440VAC (model D). Nominal rating is 380/400VAC.
432VAC to 528VAC (model E). Nominal rating is 480VAC
Frequency Rated 47 through 63 Hz
Efficiency >91% (typical), nominal line, full load.
Max Current, per phase,
low line
  400/380Vac 480Vac
10kW unit (1 module) 21Arms 17Arms
20kW unit (2 modules) 42Arms 33Arms
30kW unit (3 modules) 63Arms 50Arms
Current Inrush 200A Typical
Power Factor >0.9 @ Full Load and at nominal line
Brownout Provisions Designed to meet SEMI F47-0706, S3, S8, S14 at nominal input voltages
Voltage Output 10kW 20kW 30kW Noise (pk-pk) *** Noise (RMS) ***
40Vdc 250A 500A 750A 150mV 40mV
60Vdc 167A 334A 501A 150mV 40mV

(*) Measured at the load terminals, with 1uF in parallel and 6ft of low-inductance load cable with supply operating at full load and nominal input line voltage.
(**) RMS noise is measured directly across the output terminal with supply operating at full load and nominal input line voltage.
(***) Value is for 30kW, single voltage models. Other variations may increase value by 2x.

Sense To compensate load cables voltage drop, units can generate 2% additional voltage at full scale of output voltage.
Load Regulation (Specified at No load to Full load change, nominal AC input)
Voltage 0.1% of maximum output voltage/ current
Current 0.1% of maximum output voltage/ current
Line Regulation (Specified at ±10% of nominal AC input, constant load)
Voltage 0.05% of maximum output voltage/ current
Current 0.05% of maximum output voltage/ current
Transient Response A 50% step load will recover to within 0.75% of original value within 1mSec
Stability ±0.05% of set point after 8 hrs. at fixed line, load and temperature. After 30min warm-up.
Analog Remote Programming
Voltage Accuracy 0.5% of full scale
Current Accuracy 1% of full scale
Power Accuracy 1.5% of full scale
Voltage Monitoring 0.5% of full scale
Current Monitoring 1% of full scale
Power Monitoring 1.5% of full scale
Programming range 0-10Vdc, 4-20mA
Output Float Units maybe put in series with the float limit of output terminals must be within ±150V of chassis potential
Parallel Multiple units can be paralleled to form higher power systems. Chassis control loops are tied together so that resulting higher power systems have the same transient response as a 30kW system. Control commands are only required to be sent to "master" supply. Parallel supplies require a shielded CAT 5 cable (STP) and appropriate output wiring connections by the user.
Calibration End user calibration is supported. All standard and digital calibration can be performed without removing covers.
Digital Control (Optional) Ethernet (Modbus-TCP or Ethernet/IP), RS-485 (MODBUS-RTU)
Analog Control All control signals are isolated from the outputs
Advanced Digital Features (Requires Optional Digital Control):
Graphical User Interface Graphical User Interface (Windows based) enables remote control and display of the supply operation including the a dvanced features listed below:
Oscilloscope Function
(125 Hz)
Up to two parameters; Voltage, current, output impedance, output cable impedance, output cable voltage drop, power delivered…
Data logging Programmable update rate of 1 sec to 1000 sec (default 10 sec) with last 1000 points stored. Stored parameters include, output voltage/current, programmed set points, input voltage, output impedance, cable impedance, total power deliver, power meter, internal faults
System fault reporting Outside of set point, output impedance (detection of cabling, connection or load problems)
  30 kW 20 kW 10 kW
Width 19.00in (48.3cm) 19.00in (48.3cm) 19.00in (48.3cm)
Depth 30.00" (76.2 cm) 30.00" (76.2 cm) 30.00" (76.2 cm)
Height 3U-5.22" rackmount (13.25 cm) 3U-5.22" rackmount (13.25 cm) 3U-5.22" rackmount (13.25 cm)
Weight ≤125 lbs (56.69 kg) ≤125 lbs (56.69 kg) ≤125 lbs (56.69 kg)
Shipping Weight Contact factory for more product & shipping weights
Mounting provisions EIA rack-mount with slide provisions. Recommended rack slide: Jonathan slide, P/N 370EZ-28
AC Input Connector Phoenix Contact terminal block
Protective Ground 1/4-20 stud
Output Connectors bus bars with 3/8-16 inserted PEM nuts
Water Connections 3/8-18 NPTF hex bulkhead
Ambient Temperature 0 to 50ºC
Humidity Relative humidity up to 95%, non-condensing
Water cooling specifications
Flow 1.5 gpm nominal, 1.25gpm minimum, 1.75gpm maximum. Internal condensation must be prevented by ensuring that the temperature of the coolant is sufficiently high compared with the ambient air dew point
Temperature 25ºC nominal, 20ºC minimum, 30ºC maximum
Maximum pressure 80 PSI
Pressure drop typical 12 PSI @ 1.5gpm per chassis
Certified to UL/CSA 61010 and IEC/EN 61010-1 by a NRTL, CE Compliant, LVD Categories: Installation Category II: Pollution Degree 2; Class II Equipment: for Indoor Use Only. Rack mount equipment requires proper enclosure provided in end use. EMC Directive, EN 61326:1998

DC Product Selector

DC Electronic Loads

DC Modular Supply

Discontinued Products

Product Support

Contact Sales